The Independent Michigan Tractor Pulling Website
HOME

TRACTORS FOR SALE

Posted 3/1/08
1947 VAC CASE. Restored and used to pull it. Good Condition. Asking $1800, or best offer.
Call 740-686-2675 or email for more information

Posted 11/10/07
900 Case turnkey puller. Less than 10 runs on overhaul and no runs on machine cut 18.4x38 BF Goodrichs. Weighs under 5000lbs. Pulls MPH or open gear. Bored and stroked. Large carb and MSD. Looks as good as it runs. $9000.00 obo
Call at 931-260-2034 or e-mail at rwatt@frontiernet.net

Posted 3/20/07
MM GVI with HD800, ready to go play, 32 degree tubeless V-cuts, strong puller. Can deliver for a fee. May take a Mopar rod project on trade. $6500 obo
Call 812-394-5704 or email for more info

Posted 3/3/07
1952 Farmall H, S.E.A.T.P point champ 4000# and 3rd in 4500#, pulls up to 5000#. 50+ hp, comes with 14.9 x 38 Firestone tires on steel press wheels and a set of 15.5x38 Goodyears on cast wheels, both sets are cut. Front and rear weight brackets, wheelie bars, dead mans throttle, K&N filter, ported and polished head, intake, and carb. This tractor is very nicely restored like a Farmall demonstrator.
Any ?'s feel free to email or call 507-438-4427. MUST SELL!!

Posted 1/28/07
INTERNATIONAL 1466, Weighs right around 9300 LBS. Ready to Run. This tractor has pulled in Hot Farm and Farm Stock. 436 motor, 13mm pump, 120 Injector lines with 4 hole injectors, NEW 3LM Turbo, New Radiator, Adjustable hitch, Wheelie bars, Front, Belly, and Rear Weight Brackets, Both Narrow and Wide Front ends, B.F. Goodrich 18.4x38 tires, Firestone 20.8x38 tires, 19- 100lb weights (sold separately)
If you have any questions Email ih-puller@hotmail.com or call Kevin (616)218-4761
For pictures please go to http://www.freewebs.com/ihpuller/

Posted 1/14/07
460 IH Farmall - Points Champion of IAMO Association 5500# class. 331 cu inch motor running high RPM, block is hard blocked and o-ringed with copper head gasket, large heavy sprung intake and exhaust valves on ported and polished head, 14:1 compression ratio, BPM File Fit Rings, Berry Cam, ARP rod bolts, BRC pistons, MSD coil and electronic ignition, Fixed timing advance on distributor. Custom built intake and exhaust with custom carburetion, electric water pump, fuel pump & fan. High Capacity main clutch and torque. Flywheel and Torque safety blankets. 18.4 X 38 machine cut tires on wide rims with weld on hubs and wide front Adjustable hitch, wheelie bars, front, belly, and rear weight brackets Starts pulling at 4500# weight classes up through 7500#. $6700
For pictures - http://www.iamopullers.com/new_page_29.htm
Call (660) 359-1890 or email big97rob@yahoo.com

Posted 12/17/06
The Godfather Reloaded:
A 2, 3, 4 or 5 engine modified pulling tractor built by Ronnie Reed. Can be pulled in the 5500 - 10500lb classes. New Puller 2000 30.5 tires, 572 cu. in. Aries engines, 14-71 blowers, freshly redone, new paint, 4 fresh motors, 25ft. enclosed hauler trailer, lots of extra parts, too many to list, complete pulling setup. $80,000
Call 209-495-1818. Out of Hilmar, CA [Email] [Photo]

Posted 11/25/06
Bill Conner’s Forced Vengence 48 cu. in. garden tractor for sale. Former winner in ITPA and good hooking tractor. Tractor has 48 ci Kohler motor with all Vogel parts and legal for all 48 ci classes. Midwest SuperCub 3 speed rearend w/ reverse. Volkswagon clutch, mikuni 44 carb, holley fuel pump, Cepek 2 ply, all aluminum wheels, starter cart, weights included and painted 2000 Dodge red paint.
Call Bill Conner at 618-629-2426 after 6 pm for more information or to see tractor.
Email for further information